Dani Fusion 2.0 Artemis

Regular price: £136.00
Sale price: £136.00
Regular price
Unit price: per

Tax included. Shipping calculated at checkout.

Quantity must be 1 or more

The Dani Fusion 2.0 Artemis is similar to the Dani Fusion 2.0 metal stem, except with the addition of a Vietnamese Tracwood Sleeve around the metal sleeve of the stem. This helps to reduce the heat which is transferred into your fingers while holding the device. This does make for slightly reduced heat transfered away from the vapor as it acts as an insulator, but makes for a more comfortable experience overall while using the stem.

The Dani Fusion 2.0 is a thoroughly redesigned and upgraded version of the original Dani Fusion torch heated vaporizer. It stays much cooler in the hand during use, has a larger capacity bowl with a half pack screen option and a higher click temperature from the cap, making for more easily repeatable sessions with less heating past the click. All in all this makes for a better vaping experience and is a worthy upgrade from the original.

The Fusion 2.0 Artemis stem provides the second most vapor cooling of the Fusion 2.0 variants, sitting very close behind the Fusion 2.0 metal stem.
The Stem is made from all stainless steel to improve vapor cooling while retaining an internal Titanium helix cooling stem
The carb hole in the side of the stem has been removed making for an easier experience, allowing you to heat the cap with your torch then crack on with vaping without the need to locate and cover the hole.
The amount of airflow can be adjusted by rotating the bowl (while cool) to expose or cover some of the 6 airflow holes built in to the tip

Heating

After loading don't screw the cap on tightly, gently does it.
There are two Silver strips around the cap of the Dani Fusion 2.0.
Using a large torch heat both rings at the same time
Wait for the click (one click, not two like a DynaVap)
Gently inhale, the heat will take a moment to start to transfer from the cap into the bowl, then vapor production will really start to kick in
For higher temperature extractions you can heat past the click for a few seconds, however be cautious as with the new Fusion 2.0 Cap which has been adjusted to click at a higher temperature there will be less time before it overheats and combusts
Make sure you're using a large enough torch, small single flame torches will take a very long time to heat the cap, we always suggest using something that's more powerful.
You can use a Blazer Big Shot Torch, Stringray, FireFox or Yocan Red Torch to heat both rings at the same time.
Or you can use the Flare Induction Heater
When you've finished your session you can hold the cap with the provided leather case or use the Leather Loop to safely remove this while hot

Other Notes

To use the microdose function, remove the tip then push the screen up from the bottom so that it sits in the groove halfway up the chamber. After that's done you can use it as normal with smaller amounts... alternatively you can leave the screen where it is and just put less inside! Both methods will provide similar results!
The Fusion 2.0 is great with solid material, break it up and sandwich it in your herb or leave a little on top of the herb. You can also use hemp cotton and load solids or concentrates on top this!
The Cooling Helix inside the stem will rattle around inside when it's new. After a few uses the residue will take care of that for you.
Of the new Fusion 2.0 Devices the all metal Dani Fusion 2.0 listed here provides the most vapor cooling, though the difference is not massive
The Silver rings on the cap of the Fusion may have some dark marks, these are tarnish marks from where the cap has been installed or from the leather case. These Silver rings can be lightly polished with a high grain buffer/nail file though when you touch the silver rings they will again start to form as the oils from your skin react with the metal and oxygen. This is normal for Silver! Torching these rings in the normal way you would when heating it for use will also generally remove these marks over time.
Link to the cleaning guide

Included Components:

Dani Fusion 2.0 Artemis Stem, Tip and Cap - with Spare O-rings
A titanium chamber that can contain 0.18g of herb.
A smart stainless steel airflow control connector.
A stainless steel CCD screen.
4 viton o-rings, each measuring 7.5-8mm in outer diameter (OD) and 1mm in thickness.
2 viton o-rings, each measuring 6mm in OD and 1mm in thickness.
An IH-compatible stainless steel cap, adorned with two silver rings.
A stem made of 100% stainless steel. This stem is composed of two super thick pipe parts that layer into each other with the help of o-rings. This design aids in cooling down the vapors more efficiently and quickly. Despite multiple continuous heating times, the stem remains cool to the touch.
3 viton o-rings, each measuring 9mm in OD and 1mm in thickness.
2 viton o-rings, each measuring 11mm in OD and 1.5mm in thickness.
3 viton o-rings for the mouthpiece, each measuring 6.5mm in OD and 1mm in thickness.
A titanium mouthpiece now with an additional o-ring for an extra secure fit
A Waxed Leather Case included.

New Features:

Long tail titanium chamber for more efficient vapor cooling.
Reduced threads (from 4 threads to 3 threads).
Half-bowl setting.
Ability to produce tasty and flavorful vapors.
XL size chamber.
The silver rings offer a fast heating feature. Each ring is positioned differently to allow customization of vaporization for MTL or DRL.
The thermal disc has a higher temperature setting compared to the Dani Fusion 1.0.
The cap is impressively thick, ensuring substantial heat retention.
There’s no need for rotation during the heating process.
Superior capability to cool down vapors.
Remains cool to the touch even after multiple continuous heating cycles.
Easy to clean removable internal stem

Dani Fusion 2.0 Artemis

Customer Reviews