The Flare 2.0 Induction Heater

The Flare 2.0 induction heater is the stealthiest and quietest way to heat your Battery Free Ganz devices. Made with adjustable wattage and an adjustable timer it makes for super easy and repeatable heating of your tip and cap setup, it's also compatible with a range of other devices (see below for further information). In the top there is a hidden cooling and storage magnet for you to pop your Fusion (or other) device on top of after a session or when not in use. This updated version has improved on reliability by using a higher quality chip/pcb and improved thermal venting to reduce overheating. It also now has a thicker user replaceable glass chamber; since knocks by users to the glass are the main cause of death for most induction heaters! 

Please note that while the Flare 2.0 is primarily designed to work with the Battery Free Ganz devices. To use it with other setups may not be 100% optimal and a little tweaking of settings and positioning may be required. 

Features

• Wattage Range 30 - 120W
• Timer Adjustable 10 - 60 seconds
• Adjustable Chamber Height (remove battery cover and push up ceramic insert from underneath) 
• OLED display
• User Replaceable Glass Chamber Tube! (Approx. 16mm Internal Diameter)
• Requires 3 x Molicel P28a or Similar Spec. Batteries 
• 6 month manufacturer warranty against defects 
• CE and ROHS Certified 
  
  

Included in box:

• BFG Flare Induction heater
• USB-C charging Cable
• 2 x Replacement Adjustable Height Ceramic Chamber Insert (One installed)
• 2 x Glass Chamber Tube (one installed) 
• Optional batteries - we will be unable to restock the molicel p28a batteries as they're no longer sold for use with vapes so we will provide others of a relevant specification when stock is gone. Those will be the Eve-30p cells which have a little higher capacity at 3000mah

Important note!!! - When you remove the glass chamber insert, pull it out of the top of the unit from the top if possible (finger inside and pull up slowly). Do not push it up from the bottom as you may dislodge the rubber gasket in the bottom of the unit if it's done incorrectly! To adjust the ceramic insert you just push it with your finger or the device you're using it with to adjust the height inside the glass tube. 

The Flare

Experience unparalleled performance with The Flare, an advanced induction heater designed by Battery-free Ganz.

Power Up: Requires 3 x MOLICEL p28A 18650 batteries (available optionally - UK Shipping Only for batteries). Always used batteries of the same type with the same charge level, ideally of the same age, it is always best to use batteries in sets to ensure they charge and discharge at the same rate since older and more used batteries will hold less charge than new ones. 

As batteries drain they cannot provide the same amount of power, so if you're using higher wattage settings please keep more charge in the batteries. If they're low on power the Flare will automatically reduce the maximum wattage when you put a device in it to avoid over-stressing the batteries and damaging them. 

Device Compatibility:

• Dani Fusion 2.0: Best results with 100W for 45 seconds - Adjust depth for different results (do not insert past the logo, heat the cap only) 
• 120W will drain your battery quickly, and there’s no need to run it that high for most setups. It will cause sensor lag and retain the heat of the cap (a note from BFG about running 120W with the fusion)
• Anvil/Vestratto: 60–70W for 25–30s, around 20mm depth (going deeper may cause overcurrent warning/cut out).
• Dynavap - 60W max suggested 
• DynaVap HyperDyn -70w max suggested unless using a VSC where you can run it a little higher
• Thermal Accumulator
• For the Tempest please use the YLL-IH 3.0 or Ispire Wand 
• Not yet tested with the Stunner 

• And more! (we will figure it out!) - Aside from the Tempest the Flare 2.0 is compatible with the same range of smaller devices as the YLL-IH 3.0 - on the product page for that there is a more extensive list of compatible devices and settings

Please note these suggestions for heating profiles are just suggestions! Since the devices will heat differently depending on the height of the ceramic insert inside there will be a little tweaking for each person. If you find your herb combusts using one of the above suggestions, reduce the time or wattage. I would always say err on the side of caution, you can always heat it a bit more if needed, but once it's combusted you have a cleaning job to do, so work up to hotter temps instead of down from them! 

If the cap material is thinner or not particularly inductive (not great for induction heaters) like the DynaVap or HyperDyn the IH will automatically limit the wattage to the maximum it can provide to it which is why suggested wattage settings are lower for these. 

Dimension: 66 x 135 x 37mm (approx. 260g without batteries)

Charging: USB-C compatible, 2 Amp input (please use a 5v charger). For optimal charging performance, use an external battery charger instead of direct charging. This unit does not have pass through charging so please charge it and use it at separate times. 

Unleash the full potential of your devices with The Flare – the ultimate in induction heating technology!

We can only ship with batteries inside the UK, if purchasing from outside the UK please source your batteries locally. We advise using Molicel p26A or p28A batteries or ones with a similar specification. If purchased with batteries from outside the UK we will edit the order and switch the unit over to the non battery version!